Customer Reviews of Plastic Syringe
The reviews are automatic translation.
Showing 1 - 20 of 44 Reviews
Extraction of ATF
On 2018-12-30 02:16:30
Convenient. I can get out of it. Since the inside of the ATF mission is a negative pressure, if you take a momentary moment, the pulling cylinder will be sucked back by negative pressure and it will be my fault. This is easy to use.
Change brake fluid
On 2018-12-20 18:03:29
It is very convenient because there is also power to suck. I used it to exchange brake fluid.
Gear oil change of moped
On 2018-10-06 19:37:45
I think that it may be easy to use. However, I think that capacity is small and if there is a large capacity.
Bleed off brake fluid
On 2018-08-19 17:04:58
Once piping is bad and air enters once, it does not come out because fluid does not come out. I handle it somewhat without washing after use, but it can be used without problems. it's recommended
For oil change
On 2018-08-09 11:48:55
It was used to extract the waste oil remaining in the oil pan during oil change. Even if there is clay to some extent it is good as it can be taken off.
I use it for the maintenance of the brake of the motorbike.
On 2017-12-06 23:37:22
The reason is unknown because it has passed a long time since purchasing, It did not move. Heat with a heat gun and pull out, I started applying silicone grease to it. It was inside the roller cabinet that we kept in a private room in the garage.
To extract oil
On 2017-11-11 10:53:03
The tip diameter is 4.5, but in reality there are only 2.8. I could not use it because it was not compatible with the nylon tube I bought to connect and use.
Manda enzyme dilution
On 2017-10-11 16:34:00
Make a spray solution with dilution magnification 3000 times in a 2 L container. Previously, I used a rubber seal syringe, but it became heavy. This product purchased because there is no rubber seal. I will observe the progress.
This review is about item#60949043.
Weighing of liquid
On 2017-09-29 15:19:12
I bought two, but one was diagonally ahead. Since it can be used, if you use it without replacing it, I got ahead. I thought that there was strength because it is plastic, but it may have been broken actually that it was bent. I bought it because it was cheap, but there was a problem on the quality.
This review is about item#60949122.
It is used for positioning of the air cylinder by manual operation.
On 2017-09-12 22:37:52
It is useful in a simple setting before completing air equipment.
Used for AC compressor OIL injection
On 2017-08-14 22:02:39
The memory paint fades due to the influence of the AC compressor OIL (Dayton POE +).
Weighing at the time of rearing Daphnia, giving raw Chlorella water
On 2017-06-29 18:59:11
Delivery is quick, polite and satisfied. Products have various sizes that are easy to use, and they are useful.
On 2017-02-15 15:48:00
It is used for refilling ink of printer. Especially it can be used without problems.
This review is about item#60949122.
When refilling liquid
On 2017-02-06 10:58:53
Since there was no gasket, it did not move smoothly. The paint of the memory is also easy to peel off.
Viscosity density measurement test
On 2017-01-12 17:48:28
In order to measure the oil, it is easy to use with a syringe without rubber and high sealing ability. Also, it is good as the scale is easy to see.
For lubrication of motorcycle clutch wire etc
On 2016-12-16 19:27:44
Since oil does not enter easily of lubricating such as clutch wire of motorcycle and accelerator wire and so on, end of clutch wire is cut to around 10 centimeters of rubber hose of tap water and when engine oil is put in the connecting cylinder and pushed I went into the hose such as clutch wire.
I use it for a motorcycle.
On 2016-11-24 15:26:19
I mainly use it to withdraw the brake fluid of the motorbike. (Air bleeding etc.) Even if it is used several times, I am satisfied because it is neither cloudy nor split if I wipe it off with a parts cleaner every time.
Epoxy bonding operation
On 2016-10-18 18:58:51
I bought 50 ml for an equal amount of epoxy adhesive, base resin, curing agent. The syringe seems to be too large at a small amount (2 ml). I will purchase a little smaller one.
On 2016-08-06 18:20:28
The piston part can not come off, although there is a suction power, only the product with a capacity of 20 ml why the liquid with the tip outer diameter of φ 3.8 mm was not suitable for suctioning.
For introduction of fuel additives
On 2016-07-21 19:11:55
Since it can not be locked, it is necessary to hold down the joint hose.
Customers Who Viewed This Item Also Bought
Matsuyoshi & Co
299.99 - 769.99 SGD