Taps / Dies
Tap dies are a type of tool for making screws. There are two types of screws: male screws that are for insertion and female screws that are for insertion. A tool for making a female screw is called a tap, and a tool for making a male screw is called a die. By tapping with this tap and die, a part called a screw is made. These two tools, taps and dies, are collectively called “tap dies”.
- Hayasaka Mfg. SKS Hand TapIt is a general tap and is used in all directions. For 3rd grade gaugeMaterial Alloy tool steel (SKS) Type of Thread M Shape M6 and below are protruding centers
- MonotaRO Spiral Tap Hex ShankIt can be attached to an electric drill with a forward / reverse switching function, and screw holes can be easily machined. The spiral shape allows chips to be discharged upward, making it suitable for blind hole drilling. For threading blind holes. * Do not use for any purpose other than its in... Read MoreHex Width Across (mm) 6.35 Type of Thread M
- TRUSCO Extractor (Spiral Type)Bolts that are broken in the screw holes can also be removed without damaging the screw holes. For pulling out broken bolts and pipes. * Cannot be used for hardened bolts and stainless steel bolts.Material S45C
- MonotaRO Extractor + spiral typeIt is possible to remove broken bolts without damaging the screw holes. For removing broken bolts * If excessive force is applied, it may break. * Cannot be used for heat-treated bolts. * Handle is not included.Material Chromium molybdenum (heat treated) Hardness HRC43~47
- LIGHT SEIKI Round Die Metric Thread (M) Outside Diameter 38Outer Diameter (Φmm) 38 Thickness (mm) About 13 Type of Thread M Material SKS2
- MonotaRO Spiral Tap Steam TreatingIdeal for female thread machining of blind holes. Since it is homotreated, it is difficult to weld and achieves a long life. For general mild steel * Be sure to wear protective equipment when using as there is a risk of injury. * Do not use for any purpose other than its intended purpose.Chamfer 2.0~3.0P Number of Flutes 3 Spiral groove angle (°) 40 Shape Below M6 is the protrusion center. Finish Processing For blind holes Material High speed tool steel (HSS-E) Surface Treatment Homo processing Accuracy Grade JIS Class 2 equivalent Type of Female Thread Metric screw
- TRUSCO Extractor Combination (Square Type)Bolts that are broken in the screw holes can also be removed without damaging the screw holes. * Cannot be used for hardened bolts and stainless steel bolts.Material S45C
- TRUSCO Extractor (Square Type)A type that can be used for both left and right bolts and screws. For pulling out broken bolts and pipes. * Cannot be used for hardened bolts and stainless steel bolts.Material S45C
- TRUSCO Folding tap removal tool (for three grooves)A tool that allows you to easily remove the folded tap without damaging the thread when the tap is broken in the middle. Since the claw uses a special hard wire, it has high torsional strength and is hard to break, so even a strongly bitten fold-in tap can be easily removed. Even if your nails ar... Read MoreMaterial S45C Type of Thread PT
- TRUSCO Extractor Combination (Spiral Type)Even bolts that are broken in the screw holes can be removed without damaging the screw holes. For pulling out broken bolts and pipes * Cannot be used for hardened bolts and stainless steel bolts.Material S45C
- TRUSCO Hexagon Sarae Nut Die (Unified Fine Screw)Material Low alloy steel (SKS) Type of Thread UNF
- TRUSCO Folding Tap Removal Tool (Four Claws)A tool that allows you to easily remove the folded tap without damaging the thread when the tap is broken in the middle. Since the claw uses a special hard wire, it has high torsional strength and is hard to break, so even a strongly bitten fold-in tap can be easily removed. Even if your nails ar... Read MoreMaterial S45C Type of Thread PT
- Ishihashi Seiko Spiral tap (inch)The machinability is good and the chips roll up in a curl shape.Material High speed tool steel (SKH) Type of Thread W
- Light Tap Dice Set M-320It comes in a variety of sizes and is suitable for a variety of tasks. Thread correctionMass (kg) 7 Trusco Part No. 751-2988 Processing screw Metric screw Tap Grade P3 gradefrom ₱57,522.34Min. 2 days
- RIDGID (Emerson Japan) Screw extractor set NO.3You can easily remove the bolt by drilling a pilot hole in the folding bolt, driving an extractor into it, and turning it. For removing broken bolts * Cannot be used for stainless bolts. * Nuts are not included with 35560, 35565, and 35570. You can turn the body directly with a wrench.Trusco Part No. 494-7355 Set Contents 35545、35550、35555 Material Cold drawn steel pipefrom ₱3,124.46Min. 3 days
- OSG Spiral Tap General Use EX-SFT / Screw Type: MUsed for blind holes, it is suitable for work materials in which chips are continuously coiled in carbon steel, alloy steel and non-ferrous metals. Medium carbon steel (C0.25% -0.45%): ○, Alloy steel: ○, Ductile cast iron: ○, Copper: ○, Brass: ○, Brass casting: ○, Bronze: ○, Rolled aluminum mater... Read MoreMaterial High vanadium high speed (HSSE) Type of Thread M
- MonotaRO Hand Tap SetA set of general hand taps for cutting female threads. It is a 3-piece set with 9 mountains (first # 1), 5 mountains (middle # 2), and 1.5 mountains (top # 3). It is mainly used when manually cutting a thread or when correcting a thread. For thread cutting and thread correction of general female ... Read MoreAccuracy JIS Class 2 equivalent Type of Thread M
- YAMAWA Spiral Tap (M) N-SPThe spiral tap has good machinability because it removes chips toward you. Usually used for blind holes. * If you order by cash on delivery, it may be shipped the next day or later.
- OSG Point Tap Stainless Steel EX-SUS-POT Screw Type: MUsed for stainless steel through holes with poor machinability, it exhibits excellent sharpness and durability. In addition to stainless steel, it is also suitable for various heat-resistant steels and tough nickel-chromium-manganese steel. Stainless steel (~ 35HRC): ◎, copper: ◎, thermoplastic: ◎Chamfer 4P Material High vanadium high speed (HSSE) Surface Treatment Homo processing Type of Thread M
- MonotaRO Extractor Set Spiral TypeFor removing broken bolts * If excessive force is applied, it may break. * Cannot be used for heat-treated bolts. * Handle is not included.Hardness HRC 43~47 Material (Case) Bottom: ABS lid: PE Material Chromium molybdenum (heat treated) Tip Diameter (mm) NO.1:2 NO.2:3 NO.3:4 NO.4:5.5 NO.5:7 Base Diameter (Φmm) NO.1:4 NO.2:5 NO.3:6.5 NO.4:8.5 NO.5:12 Overall Length (mm) NO.1:53 NO.2:60 NO.3:69 NO.4:77 NO.5:84
- MonotaRO Hand Tap Plug Tap #2A general hand tap that cuts the thread of a female thread. The bite part is a tap in 5 mountains (2nd tap). It is mainly used when manually cutting a thread or when correcting a thread. For thread cutting and thread correction of general female threads. * Be sure to wear protective equipment whe... Read MoreChamfer Length Lcf 5 Accuracy JIS Class 2 equivalent Type of Thread M Type Medium # 2
- TPT Spiral Tap for Stainless SteelSpiral taps for stainless steel are suitable for sticky materials such as stainless steel and molybdenum steel.Number of Flutes 3 Material High speed tool steel (HSS-E) Surface Treatment Homo processing Type of Thread M Shape M3 to M6 are protruding centers.
- Ishihashi Seiko Hand In TapIt is a general tap and is used in all directions.Material Alloy tool steel (SKS)
- Hayasaka Mfg. Hexagonal Spiral TapUses HSS steel with excellent wear resistance It can be attached to models with forward and reverse rotation such as impact drivers, and screw holes can be easily machined. Chips are discharged upward by the spiral groove. (Compatible with class screws) Thread formation / correction of crushed th... Read MoreShank Diameter (Φmm) 6.35 Overall Length (mm) 70 Material High speed tool steel (HSS) Abrasive Materials Iron, aluminum, brass Type of Thread M
- OSG Point Tap General Use EX-POT Screw Type: MIt is used for general purposes and is suitable for work materials in which chips are continuously coiled in carbon steel, alloy steel and non-ferrous metals. Since the chips are surely pushed forward, there is no need to worry about chip damage. Medium carbon steel (C0.25% ~ 0.45%): ○, High carb... Read MoreChamfer 5P Material High vanadium high speed (HSSE) Type of Thread M
- TRUSCO Hand tap (set)Both through holes and blind holes can be used. High speed steel (HSS-E) tap set. Work Material: General Steel, Low / Medium Carbon Steel, Alloy Steel.Screws (Processing screw) Metric screw Set Contents Destination, middle, top Material High speed tool steel (HSS-E) Accuracy JIS Class 2 Type of Thread M Surface Treatment Non-coated
- SKC For hexagon Sarae nut dies / metric threadFit into a wrench for hexagon nuts and use for bolts and screws * There may be no manufacturer's stamp. * The dimensions of the width across flats are approximate.
- TRUSCO Tap HandleOne-character type handle for hand taps and hand reamers. Handle for tap stand * Please use the handle that matches the size of the hand tap. Be sure to use tapping oil when tapping. If you do not tighten it strongly with pliers, the tap will spin freely and your nails may be damaged. Please wear... Read MoreType For taps
- YAMAWA Plus Series Point Tap +PO* If you order by cash on delivery, it may be shipped the next day or later.Thread Number of Chamfer 5 mountains Type of Thread M
- TPT Point tap for stainless steelIn addition to stainless steel, it is also suitable for various heat-resistant steels. For through holesNumber of Flutes 3 Finish Processing For through holes Material High speed tool steel (HSS-E) Surface Treatment Homo processing Type of Thread M Shape M8 and below are protruding centers.
- MonotaRO Hex axis drill tapSince the tip is drill-shaped, it is a convenient tool that can perform pilot hole drilling and thread cutting at the same time. For easy screw hole processing. * When using with an impact driver, please work carefully. * Cannot be used except with forward and reverse rotation. * Cannot be used f... Read MoreHex Width Across (mm) 6.35
- OSG Spiral tap + for stainless steel + EX-SUS-SFT + screw type: MSuitable for blind hole stainless steel, copper and thermoplastics. Stainless steel: ◎, copper: ◎, thermoplastic: ◎ * The accuracy column is the recommended tap accuracy for class 2 female threads. * Before production in July 2002, M3 and below are protruding centers. * Tap accuracy does not guar... Read MoreMaterial High vanadium highs HSSE Surface Treatment Homo processing Type of Thread M
Filter by categories