Car Body Repair Supplies

For sheet metal bending work (square bending, R bending) and smoothing work. For sheet metal work.

New collision safety standard body compatible model. Impact welding force of AC spot. Great power with just this. Since it is an AC type, welding of up to 2.5 mm + 2.5 mm + 2 mm is possible. Pressurization adjustment is easy with a scale from 0 to 125 kg. Since the arm protector is standard equip... Read More

It is convenient to pull out the washer welded to the dented car body. Weight weight is 850g *This product is a tool that pulls out the welded washer in the dented area and corrects the dent. Do not use it for anything other than its intended purpose. *Keep your hands and face away from the shaft... Read More

It is also used as a hole plug to protect the contact surface between the bumper rubber attached to the bonnet, door and trunk and the body. These stickers are often peeled off during sheet metal and painting work, and it is troublesome to check the genuine part number, so it seems that you often... Read More

Grasp the edge of the galvanized iron plate and apply light force to bend it easily. If you bend it enough, change the scissors and squeeze it, and that's OK. You can work easily by using this even when opening.

A vacuum type slide hammer that does not damage the surface of the car body. By pumping the vacuum pump, the vacuum cup is adsorbed and sticks perfectly to the car body. Welding washers can also be pulled by using the attached hook. During sheet metal work. * Please use it after fully understandi... Read More

Make a bending line for sheet metal processing, or hit the corner from the inside after bending to finish the corner cleanly.

Ideal for pulling out all damage except the press line. Since it is designed to allow electricity to pass through easily, it is often attached to high-strength steel plate panels, and even when used with a conventional stud welder, it does not easily burn back. Copper plating with good electrical... Read More

A small hand-held metal fitting tool that hits the back of the panel. Please select this board consisting of various combinations of faces according to the shape of the correction panel. Make the best use of the elasticity and restoring force of the steel plate panel to correct it.

Drawer puller for car body * Please degreas the part you want to pull out with thinner etc. in advance. * The welded part is not strong at high temperatures, so be sure to return it to room temperature before pulling it out. * Do not place this product in a place where the temperature exceeds 40 ... Read More

It is a sticker attached to the new car. After replacing the panel, close the hole with a sticker. Most cars can be covered. 50 stickers per sheet. It is cheaper than buying a genuine product.

It can be fixed using the lock part of the door. Compatible with most car models. It can be easily attached and detached.

This product is a full set of polyester resin, glass mats, other auxiliary materials, tools, etc. required for FRP molding and repair.

A slide hammer that can be pulled by stud welding. A tool that slides a weight toward you, hits it against a stopper, and uses the impact to pull out a dent. For sheet metal work. * Do not use for any other purpose.

You can easily bend, expand, and modify the fender's claws with this one unit. Even difficult nail folding work is easy and beautiful. For bending, expanding, and correcting fender claws. * When using this product, be sure to jack up the car body and use it with the jack stand attached. * Ple... Read More

A Narashi hammer that is frequently used for standard launching of seat panels. The other side of the head is driven with moldings.

The special cosmetic nut can be removed cleanly

A thin plate is sandwiched and bent. Crush the bent (sea) part of the thin plate. The tip is curved.

Replacement tip for Monotaro welding slide hammer. Order code: for 10558215 * Do not use for any other purpose.

The striking part can be turned and squeezed when hit.

It is a wide striking surface. The handle is made of light, durable and elastic hickory. The head hardness is HRC40-50.

We perform bending and crushing of thin iron plates. The work is not easily scratched.

Ideal for pulling out intricately damaged press lines. Since it is designed to allow electricity to pass through easily, it is often attached to high-strength steel plate panels, and even when used with a conventional stud welder, it does not easily burn back. Copper plating with good electrical ... Read More

It is a sheet metal hammer for vehicles that plays 9 different roles by exchanging the head. Hammer set for high-strength steel plate and aluminum body. For automobile sheet metal work * Please wear work gloves when using. * Please do not use for any other purpose.

Insert it under the work and hit the work to punch it out.

A thin plate is sandwiched and bent. Crush the bent (sea) part of the thin plate. The tip is flat.

A slide hammer kit for repairing sheet metal in automobiles. Use a powerful slide hammer to repair damaged parts (distortion, dents, etc.) of sheet metal. Various sheet metal work can be done while using 5 types of tip attachments properly. It is an easy-to-use tool set that does not require larg... Read More

Ring tip with leaf spring for various washer welding

It can be fixed using the lock part of the door. Compatible with most car models. It can be easily attached and detached. For sheet metal work on doors and sheet metal work on rear gates.

Ideal for pulling out all damage except the press line. Since it is made of a material that allows electricity to easily pass through, it has excellent bite even on high-strength steel plates, and even when used with a conventional stud welder, it does not easily burn back. For pulling out damage... Read More

Needle tip for BS puller

Welding washer hook for pulling out the body. The holder body is made of aluminum alloy and is light and strong. * We recommend using the separately sold KOTO original hammer shaft and joint metal fittings.

Compatible with ordinary cars to large cars. Protect your computer from surge currents during welding. With this, it protects the computer circuit installed in the car from the surge current generated when using "spot, mig, TIG, plasma, stud, etc." and prevents malfunction. * Do not con... Read More

Easy to use, 30 cm long. The soft cushion handle absorbs the shock. Made of strong alloy steel. The panel replacement time can be shortened. The two sharp cutting edges bite between the panel and the side edges, allowing the panel to be peeled off. Due to the characteristic blade shape, the panel... Read More

A hammer dedicated to shibori work on the Yamagata grid on the head.