It is a set-free belt that does not stretch or shrink over time during use and is suitable for multiple hangings, and can be expected to have a long belt life. In addition, it is easy to obtain by handling it as a standard V-belt.
Operating Temperature Range (℃) -40～+70 Belt Height (mm) 11.0 Minimum Pulley Diameter (mm) 150 Belt Top Width (mm) 16.5 Maximum Speed (m/sec) 30 Offset Angle (°) 40 Electrical Resistance Value 50MΩ or more Belt Shape B Material (Belt) Rubber Type V-belt
A large reduction ratio can be obtained. (Generally up to 1:7) A relatively long distance between axes (usually 4m or less) can be obtained. There is a large degree of freedom in the distance between shafts. Multi-axis transmission is possible. Both sides are available. Easy to install and replac... Read More
Single or Double Strand 1 Type Unit Material (Main Unit) Steel Included Accessories With 1 connecting link
It is a set-free belt that does not stretch or shrink during use and is suitable for multiple hangings, and can be expected to have a long belt life. In addition, it is easy to obtain by handling it as a standard V-belt.
Operating Temperature Range (℃) -40～70 Belt Top Width (mm) 22 Minimum Pulley Diameter (mm) 224 Maximum Speed (m/sec) 30 Offset Angle (°) 40 Electrical Resistance Value 50MΩ or more Belt Shape C Type V-belt
A standard spring-loaded tension measuring machine. It can be used for standard V-belt, red label V-belt, e-power series, and ultra e-power V-belt.
V-belt tension measurement
Load Range (kg) 15 Length (mm) 200 Measuring Range (mm) 60 Mass (g) 65 RoHS directive (corresponding to 10 substances) Correspondence Material Steel sheet
This is the highest quality pulley that exceeds the JIS standard (JIS B1854-1987 "general V pulley") in terms of material, processing accuracy, and balance accuracy. The disproportionate tolerance on the outer circumference is guaranteed to be 0.1% of the pulley mass. The surface treatm... Read More
Pilot Hole Diameter (Φmm) - Number of Flutes 1 Rim Width w (mm) 20 Groove Shape A
A set of pulleys that can be used as a power transmission system or deceleration unit. You can also reverse the rotation by tapping the rubber. In addition to the pulleys of three sizes, the bearing bushes are compatible with the 3mm hexagonal shafts of the work series, 2mm and 3mm round shafts, ... Read More
The largest usage record in Japan. It demonstrates high reliability. It is a completed V pulley with high quality and high balance accuracy.
* The pilot hole is not open. Please note that additional machining such as hole machining and keyway machining cannot be supported.
Pilot Hole Diameter d (Φmm) - Number of Flutes 2 Rim Width w (mm) 44 Groove Shape B
You can easily make a power unit by combining pulleys. Five sizes of pulleys, bushes, thread rubber, etc. are included, and it is possible to change the speed and power according to the work. The motor holder and pulley stay are mounted together on a resin base and can be widely used for devising... Read More
We have a wide variety of modules, number of teeth, etc., and are inexpensive and highly applicable.
* The accuracy grade is "equivalent".
Web Thickness H (mm) - Rim Diameter I (Φmm) - Keyway Dimensions, Width x Depth (mm) - Module 0.5 Backlash (mm) 0～0.10 Tooth Surface Hardness 194HB or less Pressure Angle (°) 20 Tooth Width E (mm) 5 Surface Treatment Black dyed Gear Surface Treatment Cutting Tolerance A H7 Gear Cutting Reference Plane Hole Tooth Type Normal teeth Material S45C Type Spur gear
The Type 1 Isomec bushing has two half-drilled holes and one half-screw hole, for a total of three holes. In addition, the Isomec pulley has a screw hole at the position corresponding to the screw hole of the bushing and a drill hole at the position corresponding to the screw hole of the bushing.... Read More
Type New JIS parallel key Set screw Length (inch) 1 1/4 Dimension A (mm) 107.92 Number of Set Screws 2 Mass (kg) 2.41 Allowable Transmission Torque (Nm) 3000 Dimension B (mm) 51 Hex Wrench Nominal Size for Set Screw (mm) 8 RoHS directive (corresponding to 10 substances) Correspondence Nominal Size of Set Screw (inch) W5/8
* The pilot hole diameter is the hole diameter that is pre-drilled at the time of purchase, and the maximum shaft hole diameter is the maximum hole diameter that can be machined. Please note that we cannot handle hole processing.
Number of Flutes 3 Dimension W (mm) 64 Groove Shape B Type V pulley
Achieves high precision, high load and low noise with a new arc tooth profile. A toothed belt with a new arc tooth shape that uses involute meshing. The pulley tooth shape and belt tooth shape created by the involute movement are approximated to the utmost limit to achieve excellent transmission ... Read More
Cell Spacing (mm) 5 Belt Shape 5GT Material (Main Unit) Chloroprene rubber Material (Core Wire) Fiberglass cord Material (Tooth Cloth) Nylon canvas
The Schmidt coupling is a misaligned joint that uses the crank motion of the link. The shaft can be moved in parallel. It can be driven freely within the displacement range of the driven shaft when the rotation is stopped or during load operation. Absorbs sliding and absorbs radial sliding on the... Read More
Material (Main Unit) S45C equivalent Type Schmitt coupling
Reduction Ratio 1 Pressure Angle (°) 20 Number of Teeth 20 Tooth Surface Hardness 48～53HRC Tip Cone Angle L 49 degrees 48 minutes Shape BK Surface Treatment Black dyed Type Complete Miter Gear Surface Treatment Cutting Tooth Type Gleason Tolerance A H7 Gear Cutting Reference Plane Hole Accuracy Class JIS B 1704 Class 4 Material S45C Included Accessories Set screw Heat Treatment Tooth surface induction hardening
Common specifications for vibration High-quality special plastic material (Zytel) is used for high-rigidity and high-strength cushioning material. It is hard in the twisting direction and has excellent flexibility in the twisting and axial directions. Almost no maintenance is required. Compact It... Read More
Allowable Eccentricity (mm) 0.1 Allowable Deviation Angle (°) 1 Type Rubber type Axial Misalignment (mm) ±0.5
Achieves high precision, high load and low noise with a new arc tooth profile. A toothed belt with a new arc tooth shape that uses involute meshing. The pulley tooth shape and belt tooth shape created by the involute movement are approximated to the utmost limit to achieve excellent transmission ... Read More
Dimension PLD (mm) 0.686 Belt Width (mm) 50 Belt Nominal Width 50 Belt Thickness (mm) 7.41 Cell Spacing (mm) 8 Belt Shape 8YU Material (Main Unit) Chloroprene rubber Material (Core Wire) Fiberglass cord Type Twin power Material (Tooth Cloth) Nylon canvas
With the unique pitch diameter adjustment mechanism, the adjustment range is wide and it can be set every 1/4 rotation of the slide piece, so delicate speed setting is possible. To adjust the pitch diameter, simply loosen the set screw, turn the slide piece the specified number of turns, and then... Read More
Rim Width w (mm) 104 Mass (kg) 12.4 Dimension t2 (mm) 19 Dimension t1 (mm) 19 Datum diameter dn (mm) 293.8 Outer Diameter D (Φmm) 304.8 Number of Flutes 5 Dimension I (mm) 66 Boss diameter d (Φmm) 95 Groove Shape B Type VP pulley
The length of the free length series can be freely specified in 1 mm increments. We use high-precision cold drawing material to guarantee accuracy and minimize variations in lots. SUS316 is used for the stainless steel material to improve corrosion resistance.
Suitable Shaft Diameter (Φmm) 20～25 Width Tolerance (mm) 0/-0.036 Height Tolerance (mm) 0/-0.036 Height h (mm) 7 Width b (mm) 7 Tolerance Width: h9, height: h9 Chamfer c (mm) 0.25～0.40
Chain No. 120-2 Single or Double Strand 2 Tooth Width (mm) 22.7 Number of Teeth 50 Sprocket Shape C type Shaft Hole Type Shaft hole machining type Type Sprocket
You can expect a long belt life. In addition, it is easy to obtain by handling it as a standard V-belt.
Operating Temperature Range (℃) -40～+70 Belt Top Width (mm) 12.5 Maximum Speed (m/sec) 30 Offset Angle (°) 40 Electrical Resistance Value 50MΩ or more Belt Height (mm) 9 Minimum Pulley Diameter (mm) 95 Belt Shape A Material (Belt) Rubber Type V-belt
Mitsuboshi Belting V Belt Type B (Standard)It is a set-free belt that does not stretch or shrink over time during use and is suitable for multiple hangings, and can be expected to have a long belt life. In addition, it is easy to obtain by handling it as a standard V-belt.Operating Temperature Range (℃) -40～+70 Belt Height (mm) 11.0 Minimum Pulley Diameter (mm) 150 Belt Top Width (mm) 16.5 Maximum Speed (m/sec) 30 Offset Angle (°) 40 Electrical Resistance Value 50MΩ or more Belt Shape B Material (Belt) Rubber Type V-belt
