Welding Rods for Cast Iron
For castings, we refer to products used for casting, among other welding rods used for metal welding. The most commonly used material is pure nickel. In addition, there are iron / nickel and copper / nickel materials. Some have reduced the effect on the base material by not requiring the residual heat of the base material. Those that can handle not only welding between castings but also welding of iron and copper can be used for many castings. Products for coated arc welding, in which the core wire is coated with flux, etc., realize protection of the metal to be welded and stability of the arc.
TRUSCO Welding rod for castingUsing pure nickel core wire, the welded part is rough, machining is easy, welding strain and stress are less generated, and cracks are less likely to occur. The arc is stable and the slag peeling is good. Repair welding of general cast iron.- H&H Welding rod For castingThis product is a repacked product made by Nikko Molten Co., Ltd. for small-lot sales. Since it uses a nickel core wire and is coated with a special flux, it can be used with a lower current than other companies' products.Specification Arc welding rod Coating Graphite JIS Standard Z3252 DFCNi
- STAR ELECTRIC MANUFACTURING (SUZUKID) Coated arc welding rod T-1 for low voltage castingA shielded metal arc welding rod for low-voltage castings.
- NIKKO YOZAI MFG Shielded Metal Arc Welding Rod (for Cast Iron) DM-70DM-70 is a low hydrogen type welding rod for cast iron that uses mild steel core wire. Since it has very good compatibility with the base material, it is ideal for overlaying cast iron parts such as ingot cases whose material has changed due to the influence of heat. Overlay repair of ingot cases... Read MoreRoHS directive (corresponding to 10 substances) Correspondence Insulation Low hydrogen type Color Stick end / peach JIS Standard Z3252 E C St
- TASETO Casting welding rod Casting No. 35Taseto Casting No. 35 is an iron / nickel-based welding rod, which has excellent strength at the welded part, and is used for thick-walled parts and pressure-resistant parts. * If the welding rod absorbs moisture, dry it at about 100 ° C for 1 hour. * No preheating or postheating is required. * B... Read MoreJIS Standard ECNiFe-CI applicable AWS Standard ENiFe-CI equivalent
- Kobelco (Kobe Steel) Cast iron welding rodA coated rod using 55% Ni wire, which is used for welding spheroidal graphite cast iron and repairing various types of cast iron. The curability of the weld metal and heat-affected zone is small, the coefficient of thermal expansion is close to that of cast iron, and the crack resistance is good.... Read MoreAWS Standard A5.15 ENiFe-CI JIS Standard Z3252 DFCNiFefrom ₱19,731.93Min. 2 days
-
- Kobelco (Kobe Steel) Cast iron welding rodA graphite-coated welding rod that uses pure Ni core wire, and is used for butt welding and repair welding of various cast irons. The curability of the weld metal and the heat-affected zone of cast iron is the smallest among the welding rods for cast iron, and the machinability of the weld is the... Read MoreRod Length (mm) 350from ₱26,310.61Min. 2 days
- TOKUDEN Coated arc bar for cast iron FN-1It is a welding rod for cast iron repair joining by cold welding using iron-nickel core wire, and there is no difference in performance and there is a slight difference in workability. Welded metal has excellent mechanical properties and weldability, and is highly reliable for pressure-resistant ... Read MoreAWS Standard A5.15 ENi-CI RoHS directive (corresponding to 10 substances) Correspondence JIS Standard Z3252 DFCNi Coating graphitefrom ₱18,909.59Min. 12 days
- TASETO Casting welding rod Casting special nameTaseto Casting Special No. is a nickel-based welding rod that is resistant to defects such as blow holes and cracks without preheating the base metal, and is easy to machine. It is used for filling nests, joining, and repairing cracks in various cast irons. * If the welding rod absorbs moisture, ... Read MoreAWS Standard ENi-CI equivalent JIS Standard ECNi-CI applicablefrom ₱16,031.42Min. 5 days
- TASETO Casting welding rod Casting No. 1Taseto Casting No. 1 is a copper / nickel welding rod that can weld castings without preheating. It can also be machined after welding. * If the welding rod absorbs moisture, dry it at about 100 ° C for 1 hour. * No preheating or postheating is required. * Before starting work, completely remove ... Read MoreJIS Standard ECNiCu applicablefrom ₱12,330.91Min. 5 days
- TOKUDEN Coated arc bar for cast iron FN-SSince a special iron nickel core wire is used, it can be welded to the end without burning the rod. Welded metal has excellent mechanical properties and weldability, and is highly reliable for pressure-resistant parts and thick parts. The workability is also good, the welded part is less hardened... Read MoreRod Length (mm) 350 AWS Standard A5.15 ENi-CI JIS Standard Z3252 DFCNi Coating graphitefrom ₱45,187.31Min. 12 days
- CeRTANIuM Arc welding rod for all cast iron CeRTANIuM 7500Thick material of all cast iron can be melted with high current and welded well. For all cast iron, for welding castings and castings, castings and iron, etc., for welding dirty and oil-soaked engine blocks, gear housings, etc. * Please read the usage procedure manual before use.Material standard Ni，Cu，Fe，Si Rod Length (mm) 350 Current Range (A) 65-120 Rod Diameter (Φmm) 3.2 Elongation (%) 50 Hardness 170B Welding Method Manual welding AC / DCfrom ₱9,863.91Min. 6 days
- Kobelco (Kobe Steel) Cast iron welding rodA 0.5% Mo weld metal is obtained. Standard type, 0.5% steel is used for the core wire. Welding of 0.5% Mo steel used for high temperature boilers, petrochemical equipment, etc.AWS Standard A5.15 ESt JIS Standard Z3252 DFCFefrom ₱26,310.61Min. 5 days
- CeRTANIuM Arc welding rod for all cast iron CeRTANIuM 7500Thick material of all cast iron can be melted with high current and welded well. For all cast iron, for welding castings and castings, castings and iron, etc., for welding dirty and oil-soaked engine blocks, gear housings, etc. * Please read the usage procedure manual before use.Material standard Ni，Cu，Fe，Si Rod Diameter (Φmm) 3.2 Rod Length (mm) 350 Welding Method Manual welding AC / DC Current Range (A) 65-120 Elongation (%) 50 Hardness 170Bfrom ₱16,442.59Min. 6 days
- TOKUDEN Covered arc rod SN-1 for cast ironIt is a welding rod for repair and joining cast iron by cold welding using pure nickel wire, but there is a slight difference in workability. SN-1 improves the flow of weld metal, and the bead spreads better and becomes flatter than SN. Machining is easy because the welded part is less hardened, ... Read MoreRod Length (mm) 350 AWS Standard A5.15 ENi-CI RoHS directive (corresponding to 10 substances) Correspondence JIS Standard Z3252 DFCNi Coating graphitefrom ₱53,410.66Min. 12 days
- TOKUDEN Covered arc rod for cast iron ENAlthough it is a pure nickel welding rod, a special element is added to the weld metal, and it exhibits excellent performance against cracks and thermal shock as well as strength. Machining is easy because the welded part is less hardened, and it is also suitable for welding parts that receive wa... Read MoreRod Length (mm) 350 AWS Standard A5.15 ENi-CI RoHS directive (corresponding to 10 substances) Correspondence JIS Standard Z3252 DFCNi Coating graphitefrom ₱53,410.66Min. 12 days
- TOKUDEN Covered arc rod for cast iron VA-10A shielded metal arc welding rod developed as a welding material that requires machinability and wear resistance for overlay welding to cast iron. Since the component of the weld metal is alloy steel, it has higher hardness than conventional nickel-based weld metals, so it has good wear resistanc... Read MoreRod Length (mm) 350 RoHS directive (corresponding to 10 substances) Correspondence Coating Low hydrogenfrom ₱16,442.59Min. 12 days
- TOKUDEN Coated arc bar for cast iron T-SNRod Length (mm) 1000 Rod Diameter (Φmm) 2 RoHS directive (corresponding to 10 substances) Correspondencefrom ₱61,634.01Min. 12 days
- CeRTANIuM Arc welding rod for all cast iron CeRTANIuM 7500Thick material of all cast iron can be melted with high current and welded well. For all cast iron, for welding castings and castings, castings and iron, etc., for welding dirty and oil-soaked engine blocks, gear housings, etc. * Please read the usage procedure manual before use.Rod Diameter (Φmm) 3.2 Welding Method Manual welding AC / DC Material standard Ni，Cu，Fe，Si Elongation (%) 50 Current Range (A) 65-120 Rod Length (mm) 350 Hardness 170Bfrom ₱15,620.25Min. 6 days
- TOKUDEN Covered arc rod SN for cast ironIt is a welding rod for repair and joining cast iron by cold welding using pure nickel wire, but there is a slight difference in workability. SN-1 improves the flow of weld metal, and the bead spreads better and becomes flatter than SN. Machining is easy because the welded part is less hardened, ... Read MoreRod Length (mm) 350 AWS Standard A5.15 ENi-CI RoHS directive (corresponding to 10 substances) Correspondence JIS Standard Z3252 DFCNi Coating graphitefrom ₱53,410.66Min. 12 days
- TOKUDEN Coated arc bar for cast iron FNIt is a welding rod for cast iron repair joining by cold welding using iron-nickel core wire, and there is no difference in performance and there is a slight difference in workability. Welded metal has excellent mechanical properties and weldability, and is highly reliable for pressure-resistant ... Read MoreAWS Standard A5.15 ENi-CI RoHS directive (corresponding to 10 substances) Correspondence JIS Standard Z3252 DFCNi Coating graphitefrom ₱18,909.59Min. 12 days
- TOKUDEN Covered arc rod for cast iron T-FNRod Length (mm) 1000 RoHS directive (corresponding to 10 substances) Correspondencefrom ₱49,298.98Min. 12 days
- NIKKO YOZAI MFG Covered arc welding rod (for cast iron) DM-150DM-150 is a welding rod for cast iron that can be used with a lower current than other companies' products because it uses an iron-nickel core wire and is coated with a special flux. Therefore, the fusion part is less hardened and the welded part can be easily machined. It is particularly sui... Read MoreAWS Standard A5.15 ENiFe-CⅠ Applicable Current Range (A) Downward / 50-80 Insulation Graphite Color Rod end / yellow JIS Standard Z3252 E C NiFe-CⅠDiscontinued
